TKR0370 RE
Plastic stay RE – Frame screw-in stay
Properties
- Plastic stay for light and medium loads. Assembly without screws.
- Available in 5 widths.
- Outside/inside: to open by rotating.
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
Bi
[mm]
|
Bk
[mm]
|
qk
[kg/m]
| ||||
|---|---|---|---|---|---|---|---|---|
| 28 | 35 | 40 | 50 | 60 | 70 | 80 | Bi + 19 | 0.53 – 0.61 |
KR
[mm]
| ||
|---|---|---|
| 55 | 75 | 100 |
Order example
TKR0370
80
RE
75
703
VS
Inner distribution
The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (Version A).
Fixable dividers are available for applications with lateral accelerations and for applications lying on the side.
The arresting cams click into place in the locking grids in the crossbars (version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 7.5 | 8 | 6 | – | – |
| B | A | 8 | 6 | 2 | – |
| A | Bi [mm]
aT min [mm]
| 40 8 | 50 9 | 60 8 | 70 9 | 80 8 |
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 7.5 | 8 | 6 | – | 2 |
| B | A | 8 | 6 | 2 | 2 |
| A | Bi [mm]
aT min [mm]
| 40 8 | 50 9 | 60 8 | 70 9 | 80 8 |
Order example
TS1
A
3
VD0
VD1
End connectors
UMB end connectors UMB – plastic
The universal mounting brackets (UMB) are made from plastic and can be mounted from the top, from the bottom or face on.
Recommended tightening torque:
0,6 Nm for screws M4
Bi [mm] |
BEF [mm] | nz |
|---|---|---|
40 | 59 | 3 |
50 | 69 | 4 |
60 | 79 | 5 |
70 | 89 | 6 |
80 | 99 | 7 |
F – fixed point
M – driver
U – universal mounting bracket
Order example
UMB
F
U
UMB
M
U
UMB
UMB
F
M
U
U
