United States
Call: 800.323.7790 | |  

Q040 RE

Plastic stay RE – screw-in frame stay

Q040 RE Start
Q040 RE Stay variants
Properties
  • Plastic profile bars for light to medium loads. Assembly without screws.
  • Available customized in 8 mm sections.
  • Outside/inside: release by rotating 90°.
Stay arrangement on every 2<sup>nd</sup> chain link

Stays on every 6th section, standard (HS: half-stayed)

Stay arrangement on every chain link

Stays on every 3rd section (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 8 mm increments
Bi 28 – 284 mm in 8 mm width sections
All pictographs

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
hi
[mm]
hG
[mm]
Bi
[mm]
Bk
[mm]
qk
[kg/m]
28 40 28 36 44 52 60 68 76 84 92 100 108 116 124 132 140 148 156 164 172 180 188 196 204 212 220 228 236 244 252 260 268 276 284 Bi + 40 0.63 – 0.98
* in 8 mm width sections
KR
[mm]
607590110150180

Order example

Order code

Q040

108

RE

150

1290

HS

Our technical support can provide help for gliding arrangements: engineeringsupport@kabelschlepp.com

Inner distribution

Divider systems

The divider system is mounted on each crossbar as a standard – on every 6th section for stay mounting (HS).
As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).

For applications with lateral accelerations and applications with the cable carrier rotated by 90°, the dividers can easily be fixed by turning the frame stay by 180°. The arresting cams click into place in the locking grids in the crossbar (version B). The groove in the frame stay faces outwards.

Divider system TS0

without height separation
Q040 RE TS0 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A885.2
B1485.28

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS1

with continuous height separation
Q040 RE TS1 EN
Vers.
aT min
[mm]
aT max
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A82085.22
B142085.282

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS2

with partial height separation
Q040 RE TS2 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B128*/245.2*/21.282

* for VR0

With grid distribution (8 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section (version A) or fixed (version B).

Order example

Order code

TS2

A

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS2), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.

 

End connectors

Universal end connectors UMB – plastic  (standard)

The universal end connectors (UMB) are made from plastic and can be mounted from the top, from the bottom or face on.

Q040 Universal end connectors UMB – plastic (standard)
Q040 Universal end connectors UMB – plastic (standard)
Important information

Recommended tightening torque: 
5 Nm for screws M5 - 8.8

Q040 Universal end connectors UMB – plastic (standard)
Connection point

F – fixed point
M – driver

Connection type

U – universal end connector

Order example

Order code

UMB

F

U

UMB

M

U

End connector

UMB

UMB

Connection point

F

M

Connection type

U

U

Important information

We recommend the use of strain reliefs before driver and fixed point.

Subject to change.
^