HC46 RSH
Aluminium stay RSH – screw-in frame stay
Properties
- Aluminum profile bars for light and medium loads. Assembly without screws.
- Available customized in 1 mm grid.
- Outside/inside: release by rotating.
Stays mounted on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
hi
[mm]
|
hG
[mm]
|
hG'
[mm]
|
Bi
[mm]
* |
Bk
[mm]
|
qk
[kg/m]
|
|---|---|---|---|---|---|
| 46 | 64 | 67.2 | 50 – 400 | Bi + 26 | 1.83 – 4.01 |
KR
[mm]
| |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 75 | 100 | 125 | 150 | 175 | 200 | 220 | 250 | 300 | 350 |
Order example
HC 46
200
RSH
170
2010
VS
Inner distribution
The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).
For applications with lateral acceleration and lying on the side, the dividers can be attached by simple insertion of a fixing profile into the RSH stay, available as an accessory (Version B).
Le système de séparateurs est monté en standard sur chaque 2e maillon de chaîne.
En standard, les séparateurs ou le système de séparateurs complet (séparateurs avec séparation en hauteur) sont mobiles transversalement (version A).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 7 | 13 | 10 | – | – |
| B | 7 | 13 | 10 | 2 | – |
The dividers can be moved within the cross section (version A) or fixed (version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 7 | 13 | 10 | – | 2 |
| B | 7 | 13 | 10 | 2 | 2 |
The dividers can be moved within the cross section (version A) or fixed (version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 4 | 16 | 8 | 2 |
The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.
Aluminum partitions with 1 mm increments with ax > 42 mm are also available.
| ax (center distance of dividers) [mm] | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ac (nominal width of inner chamber) [mm] | ||||||||||||||||||||||
16 8 | 18 10 | 23 15 | 28 20 | 32 24 | 33 25 | 38 30 | 43 35 | 48 40 | 58 50 | 64 56 | 68 60 | 78 70 | 80 72 | 88 80 | 96 88 | 112 104 | 128 120 | 144 136 | 160 152 | 176 168 | 192 184 | 208 200 |
When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 3 mm). Twin dividers are also suitable for retrofitting in the partition system.
Order example
TS3
A
2
K1
K5
34
38
VD1
VD3
Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
Universal end connectors UMB – plastic (standard)
The universal mounting brackets (UMB) are made from plastic and can be mounted from the top, from the bottom or face on.
F – fixed point
M – driver
U – universal mounting bracket
Order example
UMB
F
U
UMB
M
U
UMB
UMB
F
M
U
U
We recommend the use of strain reliefs at the driver and fixed point.
Wir empfehlen die Verwendung von Zugentlastungen vor Mitnehmer und Festpunkt.
Nous recommandons d’utiliser des serre-câbles en amont du point mobile et du point fixe.
