United States
Call: 800.323.7790 | |  

ME1250 RE

Plastic stay RE – screw-in frame stay

ME1250 RE Start
M1250 RE Stay variants
Properties
  • Plastic profile bars for light to medium loads. Assembly without screws.
  • Available customized in 16 mm grid.
  • Outside/inside: release by turning by 90°.
Stay arrangement on every 2<sup>nd</sup> chain link

Stay arrangement on every 2nd chain link, standard (HS: half-stayed)

Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 16 mm increments
Bi 71 – 551 mm in 16 mm width sections
All pictographs

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type.
Please contact us.

Important information

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
hi
[mm]
hG
[mm]
hG'
[mm]
hG' Offroad
[mm]
Bi
[mm]
Bk
[mm]
qk
[kg/m]
72 96 99.5 103 71 87 103 119 135 151 167 183 199 215 231 247 263 279 295 311 327 343 359 375 391 407 423 439 455 471 487 503 535 551 Bi + 45 4.30 – 5.80
* in 16 mm width sections
KR
[mm]
180220260300340380500

Order example

Order code

ME1250

407

RE

300

4250

HS

Our technical support can provide help for gliding arrangements: engineeringsupport@kabelschlepp.com

Inner distribution

Divider systems

The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).

The dividers are easily attached to the stay for applications with lateral acceleration and for applications laying on their side by simply turning the frame stay by 180°. The arresting cams click into place in the locking grids in the crossbars (Version B). The groove in the frame stay faces outwards.

Divider system TS0

without height separation
ME1250 RE TS0 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A514.56.5
B19.516816

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS1

with continuous height separation
ME1250 RE TS1 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A514.56.52
B19.5168162

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS2

with partial height separation
ME1250 RE TS2 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A514.5*/206.5*/122
B19.516*/328*/24162

* for VR0

With grid distribution (16 mm grid). The dividers are fixed by the height separation, the complete divider system is movable in the cross section (version A) or fixed (version B).

Divider system TS3

with height separation made of plastic partitions
ME1250 RE TS3 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A416/42*82

* for aluminum partitions

The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.

Partitions Base

Aluminum partitions with 1 mm increments with ax > 42 mm are also available.

ax (center distance of dividers) [mm]
ac (nominal width of inner chamber) [mm]
16
8
18
10
23
15
28
20
32
24
33
25
38
30
43
35
48
40
58
50
64
56
68
60
78
70
80
72
88
80
96
88
112
104
128
120
144
136
160
152
176
168
192
184
208
200

When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 4 mm). Twin dividers are also suitable for retrofitting in the partition system.

Order example

Order code

TS3

A

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

Universal end connectors UMB – plastic (standard)

The universal mounting brackets (UMB) are made from plastic and can be mounted from the top, from the bottom, face on or from the side.

M1250 End Connector UMB
M1250 End Connector UMB
Important information

Recommended tightening torque: 54 Nm for cheese-head screws ISO 4762 - M10 - 8.8

M1250 End Connector UMB
Connection point

F – fixed point
M – driver

Connection type

U – universal mounting bracket

End connectors – plastic/steel

Plastic link end connector, steel end connector. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.

M1250 End Connector
M1250 End Connector
M1250 End ConnectorM1250 End Connector
Connection point

F – fixed point    
M – driver    

Connection type

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Connection surface

I – connection surface inside
A – connection surface outside

Order example

Order code

Plastic/steel

F

A

A

UMB

M

U

 

End connector

Plastic/steel

UMB

Connection point

F

M

Connection type

A

U

Connection surface

A

Important information

We recommend the use of strain reliefs before driver and fixed point.

Subject to change.
^