United States
Call: 800.323.7790 | |  

MC0950 RV

Aluminum stay RV – frame stay reinforced

MC0950 RV Start
M0950 RV Stay variants
Properties
  • Aluminum profile bars with plastic adapter for medium to high loads and large cable carrier widths. Assembly without screws.
  • Available customized in 1 mm grid.
  • Outside/inside: release by turning by 90°.
Stay arrangement on every 2<sup>nd</sup> chain link

Stay arrangement on every 2nd chain link, standard (HS: half-stayed)

Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 1 mm increments
Bi 75 – 500 mm in 1 mm width sections
All pictographs

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Important information

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
hi
[mm]
hG
[mm]
hG'
[mm]
hG' Offroad
[mm]
Bi
[mm] *
Bk
[mm]
qk
[kg/m]
58 80 83.5 86 75 – 500 Bi + 39 3.32 – 6.02
* in 1 mm width sections
KR
[mm]
140170200260290320380

Order example

Order code

MC0950

400

RV

200

2850

HS

Our technical support can provide help for gliding arrangements: engineeringsupport@kabelschlepp.com

Inner distribution

Divider systems

As a standard, the divider system is mounted on each crossbar – for stay mounting on every 2nd chain link (HS).
As a standard, dividers and the complete divider system (dividers with height separations) can be moved in the cross section (version A).

Divider system TS0

without height separation
MC0950 RV TS0 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A4.514102

The dividers can be moved in the cross section.

Divider system TS1

with continuous height separation
MC0950 RV TS1 EN
Vers.
aT min
[mm]
aT max
[mm]
ax min
[mm]
ac min
[mm]
nT min
A4.52514102

The dividers can be moved in the cross section.

Divider system TS2

with partial height separation
MC0950 RV TS2 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A5.521152

With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.

Sliding dividers are optionally available (thickness of divider = 4 mm).

Divider system TS3

with height separation made of plastic partitions
MC0950 RV TS3 EN
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A416/42*82

* for aluminum partitions

The dividers are fixed by the partitions, the complete divider system is movable in the cross section.

Partitions Base

Aluminum partitions in 1 mm width sections with ax > 42 mm are also available.

ax (center distance of dividers) [mm]
ac (nominal width of inner chamber) [mm]
16
8
18
10
23
15
28
20
32
24
33
25
38
30
43
35
48
40
58
50
64
56
68
60
78
70
80
72
88
80
96
88
112
104
128
120
144
136
160
152
176
168
192
184
208
200

When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 4 mm). Twin dividers are also suitable for retrofitting in the partition system.

Order example

Order code

TS3

A

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

End connectors – plastic/steel

Plastic link end connector, steel end connector. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.

M0950 End Connector
M0950 End Connector
M0950 End ConnectorM0950 End Connector
Connection point

– fixed point
– driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside

Connection surface

– connection surface inside
– connection surface outside

Universal end connectors UMB – plastic (standard)

The universal mounting brackets (UMB) are made from plastic and can be mounted from the top, from the bottom, face on or from the side.

M0950 End Connector UMB
M0950 End Connector UMB
Important information

Recommended tightening torque: 27 Nm for cheese-head screws ISO 4762 - M8 - 8.8

M0950 End Connector UMB
Connection point

F – fixed point
M – driver

Connection type

U – universal mounting bracket

Order example

Order code

Plastic/steel

F

A

U

UMB

M

U

 

End connector

Plastic/steel

UMB

Connection point

F

M

Connection type

A

U

Connection surface

U

Important information

We recommend the use of strain reliefs before driver and fixed point.

Subject to change.
^