MC0950 RS
Aluminum stay RS – frame stay narrow
Properties
- Extremely quick to open and close
- Aluminum profile bars for light to medium loads. Assembly without screws.
- Available customized in 1 mm grid.
- Outside/inside: release by turning by 90°.
Stay arrangement on every 2nd chain link, standard (HS: half-stayed)
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
hG'
[mm]
|
hG' Offroad
[mm]
|
Bi
[mm]
* |
Bk
[mm]
|
BEF
[mm]
|
qk
[kg/m]
|
|---|---|---|---|---|---|---|---|
| 58 | 80 | 83.5 | 86 | 75 – 400 | Bi + 39 | Bi + 39 | 2.93 – 4.71 |
KR
[mm]
| ||||||
|---|---|---|---|---|---|---|
| 140 | 170 | 200 | 260 | 290 | 320 | 380 |
Order example
MC0950
400
RS
200
2850
HS
Inner distribution
As a standard, the divider system is mounted on each crossbar – for stay mounting on every 2nd chain link (HS).
As a standard, dividers and the complete divider system (dividers with height separations) can be moved in the cross section (version A).
For applications with lateral acceleration and rotated by 90°, the dividers can be attached by simply clipping on a socket (available as an accessory).
This socket additionally acts as a spacer between the dividers and is available in a 1 mm grid between 3 – 50 mm, as well as 16.5 and 21.5 mm (Version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 4.5 | 14 | 10 | 2 |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
aT max
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 4.5 | 25 | 14 | 10 | 2 |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 4.5 | 23 | 19 | 2 |
With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.
Sliding dividers are optionally available (thickness of divider = 4 mm).
Please note that the real dimensions may deviate slightly from the values indicated here.
As a standard, the divider version A is used for vertical partitioning within the cable carrier. The complete divider system can be moved within the cross section.
Divider version A
End divider
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 6/2* | 14 | 10 | 2 |
* for End divider
The dividers are fixed by the partitions, the complete divider system is movable in the cross section.
| ax (center distance of dividers) [mm] | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ac (nominal width of inner chamber) [mm] | ||||||||||||||||||||||
16 8 | 18 10 | 23 15 | 28 20 | 32 24 | 33 25 | 38 30 | 43 35 | 48 40 | 58 50 | 64 56 | 68 60 | 78 70 | 80 72 | 88 80 | 96 88 | 112 104 | 128 120 | 144 136 | 160 152 | 176 168 | 192 184 | 208 200 |
When using partitions with ax > 49 mm we recommended an additional preferential central support.
Order example
TS3
A
3
K1
K4
34
38
VR1
VR3
Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
Universal end connectors UMB – plastic (standard)
The universal mounting brackets (UMB) are made from plastic and can be mounted from the top, from the bottom, face on or from the side.
Recommended tightening torque: 27 Nm for cheese-head screws ISO 4762 - M8 - 8.8
F – fixed point
M – driver
U – universal mounting bracket
End connectors – plastic/steel
Plastic link end connector, steel end connector. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
I – connection surface inside
A – connection surface outside
Order example
Plastic/steel
F
A
U
UMB
M
U
Plastic/steel
UMB
F
M
A
U
U
We recommend the use of strain reliefs at the driver and fixed point.
