ME0320 RE
Plastic stay RE – screw-in frame stay
Properties
- Plastic profile bars for light to medium loads. Assembly without screws.
- Available customized in 4 mm grid.
- Outside/inside: release by turning by 90°.
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
Bi
[mm]
|
Bk
[mm]
|
qk
[kg/m]
| |||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 19 | 27.5 | 25 | 29 | 33 | 37 | 41 | 45 | 49 | 53 | 57 | 61 | 65 | 69 | 73 | 77 | 81 | 85 | 89 | 93 | 97 | 101 | 105 | 109 | 113 | 117 | 121 | 125 | 129 | 133 | 137 | 141 | 145 | 149 | Bi + 11 | 0.46 – 1.00 |
KR
[mm]
| ||||
|---|---|---|---|---|
| 37 | 47 | 77 | 100 | 200 |
For Bi > 149 mm we recommend a multi-band chain.
Order example
ME0320
105
RE
100
1152
VS
Inner distribution
As a standard, the divider system is mounted on each crossbar – for stay mounting on every 2nd chain link (HS).
As a standard, dividers and the complete divider system (dividers with height separations) can be moved in the cross section (version A).
The dividers are easily attached to the stay for applications with lateral acceleration and for applications laying on their side by simply turning the frame stay by 180°. The arresting cams click into place in the locking grids in the crossbars (Version B). The groove in the frame stay faces outwards.
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3 | 6 | 4 | – | – |
| B | 4.5 | 8 | 6 | 4 | – |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
aT max
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|---|
| A | 3 | 20 | 6 | 4 | – | 2 |
| B | 4.5 | 20.5 | 8 | 6 | 4 | 2 |
The dividers can be moved in the cross section.
Order example
TS1
A
3
VD1
VD2
Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT].
If using divider systems with height separation (TS1), please also state the positions [e.g. VD1] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
One part end connectors – plastic/aluminum (with integrated strain relief)
The plastic/aluminum end connectors can be connected from above or below. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.
Bi [mm] | nz |
|---|---|
25 | 2 |
29 | 2 |
37 | 3 |
39 | 4 |
49 | 4 |
69 | 5 |
89 | 7 |
109 | 8 |
124 | 10 |
149 | 11 |
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
One-part end connectors – plastic/aluminum
The plastic/aluminum end connectors can be connected from above or below. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
Order example
Plastic/aluminum
F
A
Plastic/aluminum
M
A
Plastic/aluminum
Plastic/aluminum
F
M
A
A
We recommend the use of strain reliefs at the driver and fixed point.
