TKA38.080
Stay variant 080 – covered on both sides with outside detachable cover
Properties
- Plastic cover for rough environmental conditions with dirt, chips or spray water.
- Fully detachable on one side in any position.
- Outside: very quick release.
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
Bi
[mm]
|
Bk
[mm]
|
qk
[kg/m]
| |||||
|---|---|---|---|---|---|---|---|---|---|
| 26 | 36.75 | 25 | 38 | 58 | 78 | 103 | 130 | Bi + 16 | 0.77 – 1.47 |
KR
[mm]
| ||||||
|---|---|---|---|---|---|---|
| 70 | 95 | 120 | 145 | 170 | 195 | 230 |
Order example
TKA38
080
78
145
1155
VS
Inner distribution
The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (Version A).
The dividers are easily attached to the stay for applications with transverse accelerations and for applications laying on the side by simply turning them.
The locking cams click into place in the locking grids in the covers (Version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3.5 | 7 | 5 | – | – |
| B | A | 8 | 6 | 2 | – |
| A | Bi [mm]
aT min [mm]
| 25 8.5 | 38 9 | 58 9 | 78 9 | 103 7.5 | 130 9 |
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3.5 | 7 | 5 | – | 2 |
| B | A | 8 | 6 | 2 | 2 |
| A | Bi [mm]
aT min [mm]
| 25 8.5 | 38 9 | 58 9 | 78 9 | 103 7.5 | 130 9 |
Order example
TS1
A
3
VD0
VD1
Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT].
If using divider systems with height separation (TS1), please also state the positions [e.g. VD1] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
Universal end connectors UMB – plastic (standard)
The universal end connectors (UMB) are made from plastic and can be mounted from the top, from the bottom, or face on.
Recommended tightening torque: 3 Nm for cheese-head screws ISO 4762 - M4 x 12
Bi [mm] |
BEF [mm] | nz |
|---|---|---|
25 | 43 | 2 |
38 | 56 | 3 |
58 | 76 | 5 |
78 | 96 | 7 |
103 | 121 | 9 |
130 | 148 | 11 |
The end connectors are also available as an option without cover sheets. Please state when ordering.
F – fixed point
M – driver
U – universal end connector
Order example
UMB
F
U
UMB
M
U
UMB
UMB
F
M
U
U
