S/SX1250 RV
Aluminum stay RV – reinforced frame stay
Properties
- Aluminum profile bars for medium to heavy loads and large cable carrier widths. Double threaded joint on both sides.
- Available customized in 1 mm grid.
- Inside/outside: Threaded joints easy to release.
Stay arrangement on every 2nd chain link, standard (HS: half-stayed)
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
hG'
[mm]
|
Bi
[mm]
|
BSt
[mm]
* |
Bk
[mm]
|
BEF
[mm]
|
qk
[kg/m]
|
|---|---|---|---|---|---|---|---|
| 72 | 94 | 104 | 154 – 554 | 176 – 576 | BSt + 24 | BSt + 30 | 13.83 – 17.11 |
KR
[mm]
| ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 145 | 200 | 220 | 260 | 300 | 340 | 380 | 420 | 460 | 500 | 540 | 600 | 1000 |
Order example
S1250
400
RV
200
St
4750
HS
Inner distribution
The divider system is mounted on each crossbar as a standard – on every 2nd chain link for stay mounting (HS – half-stayed).
As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 13 | 16 | 10 | – |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 13 | 16 | 10 | 2 |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 13 | 21 | 15 | 2 |
With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.
Sliding dividers are optionally available (thickness of divider = 6 mm).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 4 | 16/42* | 8 | 2 |
* for aluminum partitions
The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.
Aluminum partitions with 1 mm increments with ax > 42 mm are also available.
| ax (center distance of dividers) [mm] | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ac (nominal width of inner chamber) [mm] | ||||||||||||||||||||||
16 8 | 18 10 | 23 15 | 28 20 | 32 24 | 33 25 | 38 30 | 43 35 | 48 40 | 58 50 | 64 56 | 68 60 | 78 70 | 80 72 | 88 80 | 96 88 | 112 104 | 128 120 | 144 136 | 160 152 | 176 168 | 192 184 | 208 200 |
When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 4 mm). Twin dividers are also suitable for retrofitting in the partition system.
Order example
TS3
A
3
K1
K4
34
38
VR1
VR3
Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.
The end dividers are part of the divider system and don‘t have to be ordered separately.
End connectors
End connectors – steel
End connectors made of steel. The connection variants on the fixed point and on the driver can be combined and changed later on, if necessary.
F – fixed point
M – driver
A – threaded joint to outside (standard)
I – threaded joint to inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
I – connection surface inside
A – connection surface outside
Caution: The standard connection variant FAI/MAI is only possible from Bk of 125 mm.
Order example
Steel
F
A
I
Steel
M
A
I
Steel
Steel
F
M
A
A
I
I
We recommend the use of strain reliefs at the driver and fixed point.
