S/SX1250 RR
Tube stay RR – frame stay, tube version
Properties
- Steel rolling stays with gentle cable support and plastic dividers. Ideal for using media hoses with soft sheathing. Easy screw connection.
- Available customized in 1 mm width sections.
- Inside/outside: Screw connection detachable
- Option: Divider systems made from steel and stainless steel ER 1, ER 1S.
Stay arrangement on every 2nd chain link, standard (HS: half-stayed)
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type.
Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
hG'
[mm]
|
Bi
[mm]
|
BSt
[mm]
* |
Bk
[mm]
|
BEF
[mm]
|
qk
[kg/m]
|
|---|---|---|---|---|---|---|---|
| 66 | 94 | 104 | 160 – 560 | 176 – 576 | BSt + 24 | BSt + 30 | 13.82 – 17.30 |
KR
[mm]
| ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 145 | 200 | 220 | 260 | 300 | 340 | 380 | 420 | 460 | 500 | 540 | 600 | 1000 |
Order example
S1250
400
RR
200
St
4750
HS
Inner distribution
As a standard, the divider system is mounted on each crossbar – for stay mounting on every 2nd chain link (HS).
The dividers are fixed through the tubes. The tube additionally serves as a spacer between the dividers (version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| B | 30 | 30 | 26 | – |
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| B | 30 | 30 | 26 | 2 |
Order example
TS1
B
3
K1
K4
34
38
VD0
VD0
Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
End connectors
End connectors – steel
End connectors made of steel. The connection variants on the fixed point and on the driver can be combined and changed later on, if necessary.
F – fixed point
M – driver
A – threaded joint to outside (standard)
I – threaded joint to inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
I – connection surface inside
A – connection surface outside
Caution: The standard connection variant FAI/MAI is only possible from Bk of 125 mm.
Order example
Steel
F
A
I
Steel
M
A
I
Steel
Steel
F
M
A
A
I
I
We recommend the use of strain reliefs at the driver and fixed point.
