S/SX0950 RS 2
Aluminum stay RS 2 – frame stay narrow, threaded joint
Properties
- Quick to open and close
- Aluminum profile bars for light to medium loads. Simple threaded joint
- Available customized in 1 mm width sections.
- Outside/inside: Threaded joint easy to release.
Stay arrangement on every 2nd chain link, standard (HS: half-stayed)
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
hG'
[mm]
|
Bi
[mm]
|
BSt
[mm]
* |
Bk
[mm]
|
BEF
[mm]
|
qk
[kg/m]
|
|---|---|---|---|---|---|---|---|
| 46 | 68 | 73 | 113 – 363 | 131 – 381 | BSt + 19 | BSt + 28 | 7.55 – 8.21 |
KR
[mm]
| |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 125 | 140 | 170 | 200 | 260 | 290 | 320 | 350 | 410 | 600 |
Order example
S0950
150
RS2
200
St
2375
HS
Inner distribution
The divider system is mounted on each crossbar as a standard – on every 2nd chain link for stay mounting (HS – half-stayed).
As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).
For applications with lateral acceleration and rotated by 90°, the dividers can be attached by simply clipping onto a socket (available as an accessory).
This socket additionally acts as a spacer between the dividers and is available in a 1 mm grid between 3 – 50 mm, as well as 16.5 and 21.5 mm (Version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 12 | 14 | 10 | – |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 12 | 14 | 10 | 2 |
The dividers can be moved in the cross section.
Order example
TS1
A
3
VD0
VD1
Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT].
If using divider systems with height separation (TS1), please also state the positions [e.g. VD1] viewed from the left driver belt. You are welcome to add a sketch to your order.
The end pieces are part of the divider system and don‘t have to be ordered separately.
End connectors
End connectors – steel
End connectors made of steel. The connection variants on the fixed point and on the driver can be combined and changed later on, if necessary.
F – fixed point
M – driver
A – threaded joint to outside (standard)
I – threaded joint to inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
I – connection surface inside
A – connection surface outside
Caution: The standard connection variant FAI/MAI is only possible from Bk of 122 mm.
Order example
Steel
F
A
I
Steel
M
A
I
Steel
Steel
F
M
A
A
I
I
We recommend the use of strain reliefs at the driver and fixed point.
