UA1455.040
Stay variant 040 – with inside opening and detachable crossbars
Properties
- Weight-optimised plastic frame with particularly high torsional rigidity.
- Swivable and detachable left or right in any position.
- Inside: openable and detachable.
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type.
Please contact us.
Design 040 is not suitable for gliding arrangements.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
Bi
[mm]
|
Bk
[mm]
|
qk
[kg/m]
| |||||
|---|---|---|---|---|---|---|---|---|---|
| 26 | 36 | 25 | 38 | 58 | 78 | 103 | 130 | Bi + 16 | 0.73 – 1.10 |
KR
[mm]
| ||||||
|---|---|---|---|---|---|---|
| 52 | 65 | 95 | 125 | 150 | 180 | 200 |
Order example
UA1455
040
78
150
1456
VS
Inner distribution
The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).
For applications with lateral acceleration and lying on the side, divider with arresting cams are available.
The locking cams click into place in the locking grids in the crossbars (version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3.5 | 7 | 5 | – | – |
| B | 4/5** | 7.5 | 5.5 | 2.5 | – |
Number of dividers for design 020 depending on Bi
Version B: not for design 020
** 4 mm for Bi 38 – 103; 5 mm for Bi 25, 130
| Vers. |
aT min
[mm]
|
aT max
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|---|
| A | 3.5 | 20 | 7 | 5 | – | 2 |
| B | 4/5** | 20 | 7.5 | 5.5 | 2.5 | 2 |
* not for design 020
** 4 mm for Bi 38 – 103; 5 mm for Bi 25, 130
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 3.5 | 15 | 10 | 2 |
The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.
| ax (center distance of dividers) [mm] | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| ac (nominal width of inner chamber) [mm] | |||||||||
15 10 | 20 15 | 25 20 | 30 25 | 35 30 | 40 35 | 45 40 | 55 50 | 65 60 | 75 70 |
Order example
TS3
A
2
K1
K4
34
38
VR1
VR3
Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
Universal end connectors UMB – plastic (standard)
The universal mounting brackets (UMB) are made from plastic and can be mounted from above, from below or on the face side.
Recommended tightening torque:
5 Nm for screws M5 - 8.8
Bi [mm] | nz |
|---|---|
25 | 2 |
38 | 3 |
58 | 5 |
78 | 7 |
103 | 9 |
130 | 11 |
The end connectors are optionally also available with strain relief comb (1 on each side). Please state when ordering.
F – fixed point
M – driver
U – universal mounting bracket
Order example
UMB
F
U
UMB
M
U
UMB
UMB
F
M
U
U
Single-part end connectors short – plastic
The plastic end connectors can be connected from above or below. The connection type can be changed by altering the position of the end connector.
Recommended tightening torque:
6 Nm for screws M6 - 8.8
Bi [mm] | nz |
|---|---|
25 | 2 x 2 |
38 | 2 x 3 |
58 | 2 x 4 |
78 | 2 x 6 |
103 | 2 x 8 |
130 | 2 x 10 |
The end connectors are optionally also available without strain relief comb (except Bi 25). Please state when ordering.
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
Order example
End connector
F
A
End connector
M
A
End connector
End connector
F
M
A
A
Single-part end connectors long - plastic
The plastic end connectors can be connected from above or below and allow a 1: 1 replacement of the UNIFLEX 0455 in the connection area. The connection type can be changed by altering the position of the end connector.
Recommended tightening torque:
6 Nm for screws M6 - 8.8
Bi [mm] | nz |
|---|---|
25 | 2 x 2 |
38 | 2 x 3 |
58 | 2 x 4 |
78 | 2 x 6 |
103 | 2 x 8 |
130 | 2 x 10 |
The end connectors are optionally also available without strain relief comb (except Bi 25). Please state when ordering.
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
Order example
End connector U0455
F
A
End connector U0455
M
A
End connector U0455
End connector U0455
F
M
A
A
