QT0320.040
Stay variant 040 – with inside opening crossbars
Properties
- Weight-optimised plastic frame with particularly high torsional rigidity.
- Crossbar can be opened at any position on one side
- Inside: openable.
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type.
Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
Bi
[mm]
|
Bk
[mm]
|
qk
[kg/m]
| ||||
|---|---|---|---|---|---|---|---|---|
| 20 | 25.5 | 15 | 25 | 38 | 50 | 65 | Bi + 12 | 0.35 – 0.45 |
KR
[mm]
| |||||
|---|---|---|---|---|---|
| 28 | 38 | 48 | 75 | 100 | 125 |
Order example
QT0320
040
50
100
1280
VS
Inner distribution
The divider system is mounted on each crossbar as a standard – on every 2nd chain link for stay mounting (HS).
As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 4 | 8 | 6 | – |
The dividers can be moved in the cross section.
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
nT min |
|---|---|---|---|---|
| A | 4 | 8 | 6 | 2 |
The dividers can be moved in the cross section.
Order example
TS1
A
3
VD0
VD1
Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT].
If using divider systems with height separation (TS1), please also state the positions [e.g. VD1] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
Single-part end connectors – plastic (with integrated strain relief)
The plastic end connectors can be connected from above or below. The connection type can be changed by altering the position of the end connector.
The end connectors cannot be swivelled.
Bi [mm] |
BEF [mm] | nz |
|---|---|---|
15 | 27 | 2 |
25 | 37 | 3 |
38 | 50 | 4 |
50 | 62 | 5 |
65 | 77 | 6 |
The end connectors are also available as an option without integrated strain relief. Please state when ordering.
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
Order example
End connector
F
A
End connector
M
A
End connector
End connector
F
M
A
A
